 |
Measuring expansion and shrinkage of sealant
Changes in sealant due to heat and temperature variations over time can be measured on a non-contact basis. A 0.4 μm resolution enables detection of small changes.
Product: EX-V Series
Industry: R&D
Measurement Type: Positioning, Curvature, Opening |
 |
Measuring vibration in a taping machine
Rattling in a taping machine causes displacement or running off of chip components in embossing tape.
Product: EX-V Series
Industry: IC and Semiconductor
Measurement Type: Vibration, Stroke |
 |
Measuring die distortions in a die-casting machine
Distortion and displacement of a die caused by its own weight or faulty mounting is prevented. A small and thin sensor head makes high-accuracy measurement possible even in a narrow gap in equipment.
Product: EX-V Series
Industry: Automotive/Metal
Measurement Type: Distortion, Curvature |
 |
Measuring height/curvature of piston head
Piston head concavity is measured by movement of a jig, and a type is determined.
Product: EX-V Series
Industry: Automotive/Metal
Measurement Type: Hight, Parallelism, Depth |
  |
Checking adhesion of mold press die
A fault in die adhesion is caused by displacement of lead frame. High heat resistance performance up to 105°allows direct mounting on a device, allowing high accuracy measurement in high temperature environment.
Product: EX-V Series
Industry: IC and Semiconductor
Measurement Type: Thickness, Positioning |
 |
Checking dynamic accuracy of chip mounter
Dynamic accuracy of an arm is constantly monitored during equipment operation. Faulty mounting due to a displaced home position is prevented. Ultra-compact sensor head provides excellent flexibility in installation.
Product: EX-V Series
Industry: IC and Semiconductor,Electrical/Electronics
Measurement Type: Vibration, Stroke |
 |
Detecting improper caulking
Improper caulking can be detected by checking the bottom dead center of the machine. Setting the bottom dead center mode turns on the trigger automatically and the lowest position of the bottom dead center in a sampling period is detected for evaluation of dimensional tolerance.
Product: EX-V Series
Industry: Electrical/Electronics
Measurement Type: Height, Opening |
 |
Detecting press residue
The distance between the upper die and lower die is measured upon press stamping to detect small changes of the bottom dead center caused by residue.
Product: EX-V Series
Industry: Automotive/Metal
Measurement Type: Thickness, Opening |
 |
Detecting double feeding of pressing material
Damage to a die due to double feeding of blank material is prevented.
Product: EX-V Series
Industry: Automotive/Metal
Measurement Type: Thickness, Opening |
 |
Detection of runout due to chucking failure
When a workpiece is chucked, particles are sometimes trapped between the workpiece and chuck, resulting in deflection of the workpiece. Such deflection is detected on a non-contact basis.
Product: EX-V Series
Industry: Automotive/Metal
Measurement Type: Runout, Curvature |
 |
Checking degree of vacuum in canned or sealed foods
The degree of vacuum in canned or sealed food is checked using slight dilation on a lid. The non-contact high-speed checking capability allows in-line inspection of products.
Product: EX-V Series
Industry: Food/Packaging
Measurement Type: Distortion, Level |
 |
Checking depth of bearing rim orbit
The depth of the wheel orbit slot after polishing is detected by rotating a workpiece and measuring the opening of a jig.
Product: EX-V Series
Industry: Automotive/Metal
Measurement Type: Depth |
 |
Controlling vibrations in the hopper (sieve)
The number and amplitude of vibrations in a sieve that fills powder or fluid are monitored and quantified for controlling charge volumes with high accuracy.
Product: EX-V Series
Industry: Food/Packaging
Measurement Type: Vibration |
 |
Measuring the Height at Multiple Points in a Specified Range
The average, peak or bottom height can be measured.
Warpage or swell is measured by calculating the heights at specified points
Product: LJ-G Series
Industry: Automotive/Metal, Electrical/Electronics, Food/Packaging
Measurement Type: Height, Depth |
 |
Measuring Width/gap with a Specified Measurement Mode
Width and gaps are measured on the basis of the surface profile. High accuracy measurements are carried out without being affected by the colour of targets.
Product: LJ-G Series
Industry: Automotive/Metal, Electrical/Electronics, Food/Packaging
Measurement Type: Thickness, Width, Distance |
 |
Measuring/Judging a Section in a Flash
A section area is instantly measured in a specified range. This allows for the quality control of profiles and sections.
Product: LJ-G Series
Industry: Automotive/Metal, Electrical/Electronics, Food/Packaging
Measurement Type: Thickness, Width, Height, Shape, Parallelism, Depth |
 |
Automatic Calculation of Angles/ Intersections
Angles, intersections, and edge positions are instantly measured/judged based on the surface profile.
Product: LJ-G Series
Industry: Automotive/Metal, Electrical/Electronics, Food/Packaging
Measurement Type: Positioning, Parallelism, Depth |
 |
Measuring displacement of a structure on a vibration table
With an easy setting, a major displacement is measured from a distance. Accurate measurement is possible without contact pressure against an object.
Product: LK-G Series
Industry: R&D
Measurement Type: Vibration, Distortion, Stroke |
 |
Measuring the profile of a test piece
New principles are employed for the CCD system. Regardless of color and material surface (rock, metal or rubber) high-accuracy and stable measurement are possible.
Product: LK-G Series
Industry: R&D
Measurement Type: Shape, Parallelism |
 |
Checking robotic arm position
In addition to checking halt position of a robotic arm, measurement of performance characteristics during operation can be measured at the same time.
Product: LK-G Series
Industry: R&D, Electrical/Electronics
Measurement Type: Stroke, Positioning |
 |
Measuring displacement under load test
Measuring displacement caused by a load test, on a non-contact basis, enables collection of high-accuracy data.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Curvature, Shape, Distance |
 |
Measuring displacement under load test
Measuring displacement caused by a load test, on a non-contact basis. Measurement values are input directly to a personal computer.
Product: LK-G Series
Industry: R&D
Measurement Type: Curvature, Shape, Distance |
 |
Thermal displacement test on metals
Non-contact measuring allows stable measurement of displacement of material in a high-temperature chamber through glass.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Distortion, Curvature |
 |
Measuring wear dimensions of spattering target
High-accuracy measuring of surface shape allows precise calculation of wearing.
Product: LK-G Series
Industry: IC and Semiconductor
Measurement Type: Height, Shape |
 |
Detection of double or missing chip
The LK series High Accuracy CCD Laser Measurement Sensor is used to detect rising and overlapping of chip components before cover installation. Ultra-compact size allows easy installation in equipment.
Product: LK-G Series
Industry: IC and Semiconductor
Measurement Type: Distortion, Curvature |
 |
Detecting deflection of turntable
Wide-spot laser beam allow high-accuracy measurement of a rough surface of a workpiece.
Product: LK-G Series
Industry: Electrical/Electronics
Measurement Type: Vibration, Runout, Height |
 |
Measuring shape of IC resin mold
The shape of a resin mold is measured on a non-contact basis. A state-of-the-art measurement algorithm allows precise measurement of a semi-transparent mold.
Product: LK-G Series
Industry: IC and Semiconductor
Measurement Type: Height, Shape |
 |
Measuring height of BGA ball
The difference in height among solder balls due to warpage of BGA board is measured with high accuracy.
Product: LK-G Series
Industry: IC and Semiconductor
Measurement Type: Height, Shape |
 |
Measuring warpage of a board
Warpage of a board is measured on a non-contact basis. Accurate measurement is possible on the surface of a semi-transparent board.
Product: LK-G Series
Industry: IC and Semiconductor
Measurement Type: Warpage |
 |
Measuring thickness of a pole plate
The thickness of a pole plate can be continually monitored in-line. Improper thickness can be detected immediately, minimizing waste production.
Product: LK-G Series
Industry: Electrical/Electronics
Measurement Type: Thickness |
 |
Measuring surface deflection on a hard disk
50-kHz sampling allows non-contact measuring movement characteristics of a hard disk rotating at a high speed.
Product: LK-G Series
Industry: Electrical/Electronics
Measurement Type: Runout |
 |
Measuring behavior of engine valve
50-kHz sampling allowsnon-contact measuring movement characteristics of an engine valve moving at a high speed.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Vibration, Stroke |
 |
Measurement of sand mold surface ripple
Accurate shape measurement without the influence of bad conditions such as dust particles enables the prevention of faulty casting.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Distortion, Curvature, Depth |
 |
Measuring car height while driving
The LK-G Series features an ultra long detecting distance as well as a high resolution of 10 µm in high-precision mode. Together with the fast response speed, it permits accurate data collection which is impossible with conventional sensors.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Vibration, Height, Stroke |
 |
Measuring thickness of a brake disk
The wide-spot optical system allows measurement without the influence of rough surfaces.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Thickness, Eccentricity |
 |
Measuring car height while driving
Measuring the car height is possible during a test drive.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Vibration, Height, Stroke |
 |
Measuring outer diameter immediately after lathing process
The outer diameter of a workpiece can be measured immediately after the lathing process. This prevents defective products from being continuously manufactured.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Eccentricity, Outer Diameter, Shape |
 |
Measuring noodle thickness
A laser displacement sensor measures the thickness of noodles. If the thickness is found to be abnormal a NG signal is generated. Since this is a non-contact type of detection, processes can be run with continuous monitoring and measurement.
Product: LK-G Series
Industry: Food/Packaging
Measurement Type: Thickness |
 |
Measuring end face Parallelism and width of construction board
A faulty Parallelism or faulty width caused by wearing of molding die or variations of extrusion pressure is detected.
Product: LK-G Series
Industry: Construction
Measurement Type: Width, Parallelism |
 |
Measuring eccentricity of a rubber roller
Measurement by high-speed sampling is possible even on a workpiece with low reflectivity, using state-of-the-art reflection light control.
Product: LK-G Series
Industry: Rubber/Plastic
Measurement Type: Eccentricity, Height |
 |
Checking wafer position
Checking whether a wafer set on a table is overlapping on a fixing pin.
Product: LK-G Series
Industry: IC and Semiconductor
Measurement Type: Runout, Height, Curvature |
 |
Measuring warpage of printed circuit board
With a newly developed algorithm, high-accuracy measurement is possible on a semi-transparent workpiece.
Product: LK-G Series
Industry: Electrical/Electronics
Measurement Type: Curvature, Shape |
 |
Counting packages of chemical agent
By measuring the distance between the edges of the boxes, the number of boxes can be counted.
Product: LK-G Series
Industry: Food/Packaging
Measurement Type: Shape |
 |
Detecting exfoliation or overlapping of a bottle label
When printing a date on a bottle label, exfoliation or overlapping of a label that causes a printing failure is detected at a high speed and high accuracy, preventing repeated failures.
Product: LK-G Series
Industry: Food/Packaging
Measurement Type: Thickness |
 |
Checking presence of bearing seal
The LK series high-accuracy CCD laser displacement sensor is used for preventing faulty assembling or process skipping errors on the sealing of bearings. By combining optional meter relays and measuring a rotating bearing, deflection of sealing is detected. The wide-spot optical system allows stable measurement without variation caused by roughness on sealing surface.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Height, Depth |
 |
Controlling the volume of rubber coating
The volume of rubber coating is checked before processing in an oven. The seat material is sandwiched and thickness is calculated for feedback.
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Shape, Depth, Cross Sectional Area |
 |
Measuring dimensions of a die
Dimensions of a die are measured on a non-contact basis. Accurate measurement of dimensions is possible using the Active Balanced Laser control Engine (ABLE function).
Product: LK-G Series
Industry: Automotive/Metal
Measurement Type: Shape, Depth, Cross Sectional Area |
 |
Measuring thickness of rubber sheet
The segment function allows selecting an area for measurement, which allows measuring thickness of a rubber sheet (gap between rollers) easily.
Product: LS-5000 Series
Industry: Rubber/Plastic
Measurement Type: Thickness, Opening |
 |
Measuring outer diameter and eccentricity of roller
The outer diameter of the sheet feeding roller on a copier or printer is measured on a non-contact basis. Eccentricity can be measured at the same time.
Product: LS-7000 Series
Industry: Electrical/Electronics
Measurement Type: Vibration, Outer Diameter |
 |
Measuring warpage of a connecting rod
Bending and warpage of a connecting rod after pressing is measured to prevent outflow of defective products. Measurement of two or more points is possible at the same time with connection of two measurement sets allowed.
Product: LS-7000Series
Industry: Automotive/Metal
Measurement Type: Width, Outer Diameter |
 |
Measuring the outer diameters of electrical wire (X and Y axes simultaneous measurement)
The outer diameter of an elecrical wire is measured in the X and Y axes simultaneaously, and the mean value of the diameters is calculated. Reliability is improved versus measuring only one axis.
Product: LS-7000 Series
Industry: Automotive/Metal, Electrical
Measurement Type: Width, Outer Diameter |
 |
Measuring the outer diameter of a honeycomb filter
This simple, special mode measures large diameter targets or wide sheet materials. Complicated calculations or other settings are unnecessary.
Product: LS-7000 Series
Industry: Automotive/Metal
Measurement Type: Eccentricity, Width, Outer Diameter |
 |
Measuring IC lead pitch
The measuring area can be designated according to the inspection purpose, such as measurement of the IC lead gap or pitch.
Product: LS-7000 Series
Industry: IC and Semiconductor
Measurement Type: Width, Parallelism |
 |
Checking the width or edge position of a glass plate
Even transparent objects that were difficult to detect with conventional micrometers can be measured. The edge detection level can be easily changed via the controller.
Product: LS-7000 Series
Industry:Electrical/Electronics
Measurement Type: Width, Positioning, Outer Diameter, Parallelism |
 |
Measuring the outer diameter of a fiber
The LS-7000 Series measures the outer diameter of a fiber continuously and displays not only numeral values but also a trend graph that represents the measured values in a waveform.
Product: LS-7000 Series
Industry: Electrical/Electronics
Measurement Type: Width, Positioning, Outer Diameter |
 |
Measuring the Width and Camber Parallelism of a Rubber Sheet
The positions of edges are accurately measured and output as feedback data. This prevents producing defective products caused by improper edge position while the rubber sheet is wound or transferred.
Product: LS-7000 Series
Industry: Rubber/Plastic
Measurement Type: Width, Positioning, Outer Diameter, Parallelism |
 |
Measuring the Width of Tape on Two Production Lines Simultaneously
Both the width and waving of tape can be measured. High-speed sampling enables direct measurement of the entire length of tape.
Product: LS-7000 Series
Industry: Rubber/Plastic
Measurement Type: Width, Positioning, Outer Diameter |
 |
Measuring depth of laser marker imprinting on a resin mold
The LT-9000 series double-scan laser sensor is used to measure the depth of laser marker imprinting, such as a lot number on an IC resin mold. Measurement with a resolution of 0.01 μm is possible with a view of an 85 magnified image on a monitor screen.
Product: LT-9000 Series
Industry: IC and Semiconductor
Measurement Type: Width, Depth |
 |
Measuring printing dimensions of paste solder
The LT-9000 series double-scan laser sensor is used to measure the height and dimensions of paste solder on a board. Measurement at a maximum resolution of 0.01 μm is possible. Using the world's first high-accuracy double scanning system, measurement is possible on a wet surface and a mirror-finished or a round surface. By moving a lens in the sensor, the paste of the solder paste can be measured accurately.
Product: LT-9000 Series
Industry: IC and Semiconductor
Measurement Type: Width, Height, Shape |
 |
Measuring dimensions of a specimen
Accurate tracing of a surface shape is possible with a 2 μm ultra-miniature spot diameter.
Product: LT-9000 Series
Industry: R&D
Measurement Type: Shape, Depth |
 |
Measuring surface dimensions of a resin mold product
The LT-9000 series double-scan laser sensor is used to measure surface dimensions and surface roughness of a resin mold product used in an electronic component. Measurement at a resolution of 0.01 μm is possible. The LT-9000 series allows measurement with a 85x magnified image on a monitor screen, which allows positioning a measurement target accurately.
Product: LT-9000 Series
Industry: Rubber/Plastic
Measurement Type: Shape, Parallelism |
Want to learn how to use our products?
Use our Application Finder  |
Explore the Latest Measurement System ?
Use our Product Finder 
|
|
|
German
English
Expert
Price
Unit
Catalog
)
Page Top
